Phenyl Trimethicone (CAS 73559-47-4): INCI Name, Properties, and Uses in Cosmetics — From Five Numbers on a Sheet to Behaviour in the Beaker

Hits: 2831 img

Introduction

A technical data sheet lists figures; it does not tell you what the product will feel like on hair or how a spray will look after a winter shipment. The bridge runs through four questions. What does a refractive index of 1.46 buy you? What does 22.5 mm²/s mean at the point of application? Why does solubility in 95% ethanol matter, and what does an acid value of 0.1 mg KOH/g protect you from? This article works through those translations using the published parameters of IOTA 556, the cosmetic-grade phenyl fluid from Iota Silicone Oil (Anhui) Co., Ltd., carrying the INCI name Phenyl Trimethicone and CAS number 73559-47-4.

1. What Each Published Number Buys You

The supplier’s published typical properties are reproduced below, together with their formulation consequence. The document notes that such values describe product characteristics and are not intended for use in preparing specifications, so contract terms govern acceptance.

Parameter IOTA 556 typical value Condition Consequence in the formula
Appearance Colourless liquid Visual Leaves the colour phase untouched, suited to clear and pale systems
Viscosity 22.5 mm²/s 25°C Spreads fast, settles thin, avoids a heavy afterfeel
Specific gravity 0.980 25°C Slightly lighter than water, needed for phase-separation arithmetic
Refractive index 1.46 25°C Above all-methyl systems, which is where the gloss comes from
Flash point Above 100°C As documented Reference point for handling margins in normal manufacture and filling
Acid value 0.1 mg KOH/g Titration Low free-acid content, friendlier to fragrance and active systems

Two of these decide whether the material belongs in the formula at all — refractive index and viscosity. The remaining four decide how it is used, whether it clears production, and whether it passes incoming inspection.

2. Refractive Index Is the Gloss Mechanism

Gloss is not an adjective; it is reflection at a film surface, and reflection scales with the difference in refractive index across the interface. Adding phenyl to the side groups raises that index, which is what separates phenyl fluids from all-methyl ones.

System Refractive index (25°C) Position relative to all-methyl fluid Sensory result
Dimethicone-type fluid 1.390 to 1.410 Baseline Smooth, weak reflection
IOTA 556 1.46 Roughly 0.05 higher Luminous without weight
IOTA 56A 1.498 Higher again Bright, for systems built around shine
IOTA 54 1.50 Higher again Bright with a noticeable cushioning feel

Note the ladder inside a single supplier’s range. Wanting more shine does not automatically mean changing source; re-ranking within the same family by index and viscosity frequently lands the target.

3. Where 22.5 mm²/s Sits on the Scale

Band Typical range at 25°C Feel Usual roles
Very light 1 to 20 mm²/s Disappears quickly, thin residual film Instant spread, dry finish
Light 20 to 100 mm²/s Fast spread, thin film, non-tacky Hair gloss, sprays, airy emulsions
Medium 100 to 500 mm²/s Noticeable cushion Creams, colour sticks
Heavy 500 mm²/s and above Thick film, longer residence Intensive care, hair masks

IOTA 556 sits at the lower edge of the light band, consistent with the non-oily, easy-spread character the supplier documents. Where a formula needs longer residence, blend it with a heavier grade from the same family rather than replacing it outright.

4. Alcohol Solubility Opens Specific Formats

The published solubility statement is unusually concrete: the fluid is readily soluble in 95% ethanol at room temperature, and even at temperatures as low as 4°C, up to 50% by weight dissolves in 95% ethanol.

Condition Observed behaviour Formats it unlocks
Room temperature, 95% ethanol Readily soluble, clear system Alcohol-based hair sprays, setting waters
4°C, 50% by weight in 95% ethanol Remains in solution Cold-chain storage, winter retail, fewer haze complaints
Alongside oils and emulsifiers Compatible, easily emulsified Oil-in-water creams, lotions, foundations

For spray products, clarity at low temperature is a quiet driver of returns. This statement turns that from a matter of trial into a calculation: check the solubility headroom at the lowest temperature the product will actually see.

5. Film, Feel and Finish

Documented characteristic Physical reading What the user notices
Forms a soft, invisible film A low-surface-energy liquid spreads into a continuous thin layer Original texture preserved, no visible mask
Allows natural transpiration Vapour passage differs from a dense occlusive layer Comfortable over long wear
Non-oily, easy to spread Low viscosity combined with phenyl-driven compatibility Goes on without beading up
Anti-tack, reduces stickiness Lower friction at the surface Dry finish, does not pick up dust
Adds gloss and manageability to hair Higher index plus a smoothed cuticle surface Brighter, smoother, fewer tangles

General reviews of the material class describe phenyl-substituted fluids as finishing drier and less tacky than dimethicone while carrying a higher index, which is exactly the profile wanted in formats that should look bright without feeling heavy.

6. Role in Sunscreen Systems

Published reviews point to two contributions: the phenyl structure absorbs toward the ultraviolet end, and the fluid helps dissolve and disperse certain filters.

Stage Effect Formulation caution
Filter dissolution and dispersion Less crystallisation, more even distribution Verify filter by filter
Film continuity Fewer weak spots in the deposited layer Design alongside the film-forming polymer
Sensory compensation Offsets the tack of high filter loading Adjust residue through the viscosity band

State the boundary clearly. These are formulation mechanisms. They do not substitute for a measured sun protection factor on the finished product, which requires the recognised test method.

7. Acid Value and Oxidative Stability

An acid value of 0.1 mg KOH/g is low, and it carries two implications. Free acidic material is limited, which suits systems holding fragrance and actives. And the figure suggests that stripping and finishing have kept light ends and by-products down.

The supplier also lists resistance to oxidation among the material’s features. In formulas built on vegetable oils or unsaturated esters this matters: a phenyl fluid does not replace the primary antioxidant system, but it is unlikely to become the first component to fail.

8. Mapping Targets to Parameters

Formulation target Governing parameter How to judge
Brighter hair fibre Refractive index Sensory and gloss comparison against the control
Less tack Viscosity, finish Timed tactile panel after application
Clear alcohol spray at low temperature Ethanol solubility data Hold samples at 4°C and at room temperature
Stable emulsion Emulsifiability, compatibility Centrifuge plus thermal cycling
Controlled richness Viscosity band, dose Step comparison against heavier grades
Compatibility with sensitive systems Acid value, purity figures Cross-check against the certificate of analysis

9. A Verification Routine That Holds Up

  1. Build a control formula with no phenyl fluid, so comparisons have a base.
  2. Run three small samples across IOTA 556, 56A and 54 at identical loading, using index and viscosity as the axes.
  3. Score by format: sprays on low-temperature clarity, creams on centrifuge and cycling, hair on combing work and gloss.
  4. Record dose against sensory score to find the minimum level that reaches the target.
  5. Re-measure incoming material: appearance, refractive index, viscosity, specific gravity, acid value.
  6. Write the outcome into the formula file so later sourcing and substitution rest on evidence.

10. Misconceptions Worth Correcting

Treating refractive index as the whole of gloss

Index sets the reflection potential; film thickness, uniformity and the substrate decide the result. Chasing index while ignoring uniformity produces patchy shine.

Assuming thinner is automatically better

Low viscosity brings clean spread at the cost of residence time. Intensive treatments and masks need heavier material or a blend.

Reading solubility without its temperature and ratio

“Soluble in ethanol” means little on its own. The 4°C and 50% figures are the practical boundary for a spray that must survive distribution.

Copying typical values into an acceptance specification

The supplier states these values describe characteristics rather than specifications. Acceptance should follow contract terms and batch certificates.

Letting a raw material carry a sunscreen claim

The ingredient aids dispersion and feel. The finished-product factor still has to be measured, and cannot be inferred from raw-material properties.

FAQ

What is the refractive index of IOTA 556, and how far above a dimethicone-type fluid does that sit?

The published figure is 1.46 at 25°C against roughly 1.390 to 1.410 for all-methyl fluids, a difference of about 0.05. That gap is the physical basis for the gloss effect.

What does 22.5 mm²/s feel like?

It sits in the light band: quick spread, thin film, dry finish. Paired with the documented non-oily, easy-spread and anti-tack character, it suits formats that need brightness without weight, such as hair sprays and airy lotions.

Can it go into alcohol-based formulas?

Yes, and this is where it distinguishes itself from all-methyl fluids. The supplier documents ready solubility in 95% ethanol at room temperature and solubility up to 50% by weight even at 4°C, which supports alcohol sprays and setting products while reducing cold-transport haze.

What does an acid value of 0.1 mg KOH/g indicate?

Limited free acidic material, usually a sign that stripping and finishing were well controlled. That is helpful in systems carrying fragrance or actives, and reduces variability in stability behaviour caused by raw-material drift.

Does it help with tack?

The documented feature list includes anti-stick behaviour and reduced tackiness from organic ingredients. Mechanically, low viscosity and low surface energy let the fluid spread into a continuous film that lowers friction after application, in line with general reviews describing a drier finish than dimethicone.

Can these parameters support a sun protection claim?

They cannot. The published mechanisms concern filter dispersion and film uniformity. A finished-product factor requires testing by the recognised method, and raw-material properties are not a substitute for that result.


Company note: Iota Silicone Oil (Anhui) Co., Ltd., founded in 2010 in Bengbu, Anhui, operates a 9,000 m² site with 12,000 m² of floor area, keeps R&D and international sales in Nanjing alongside long-term collaboration with several universities and research institutes, runs a documented quality system with pre-shipment testing, and offers cosmetic-grade phenyl fluids including IOTA 556, IOTA 54 and IOTA 56A with technical data sheets and samples.

Phenyl Methyl silicone oil IOTA 556 (Replacement for DC556)-IOTA

Online QQ Service, Click here

QQ Service

What's App